Sumitomo - Полный каталог инструмента - 2016 EN
для заказа - sumitomo@sumitomo-tools.ru
Recommended Grades and Chipbreakers Stainless SteelStSaitneleelss
Application Examples Insert
Selection
AC610M
X5CrNi1810, Arbour 100 - No. of Workpieces 100 -
AC610M has good wear resistance with 2x tool X510Cr13, Sleeve
life of competitor's. 100 AC610M features superior wear resistance Output (pcs) / Cutting edge 2x tool life
compared to competitor's with 2x tool life. 2x tool life
CuttingCuTittimneg(Timimn)e (min) 50 - 20
2x tool lif2ex tool life 50 -
50
10
00
AC610M Comp. M10 AC610M Comp. M10
0 AC610M Comp. M10 0
AC610M Comp. M10
InsertDNMG 150408 NEXAC610M InsertDNMG 150408 NGUAC610M
Cutting Conditionsvc=210m/min,f =0,3mm/rev,doc=2,0mm,Wet Cutting Conditionsvc=215m/min,f =0,35mm/rev,doc=0,85mm,Wet
AC630M
X5CrNi1810, Machine Component X2CrNiMo17132, Automotive Component
AC630M enables stable cutting without breakages with 1,5x the tool life of AC630M enables stable cutting even in light interrupted cutting with 2x the tool
competitor's grade. No. of Workpieces 3 3- life of competitor's grade. Output (pcs) / Cutting edge 20 -
Output (pcs) / Cutting edge
2- 11,5.5xxtotoolollifleife No. of Workpieces 20 2x tool life
2 2x tool life
10 -
1- 10
1 0
AC630M Comp. M30
0 0
AC630M Comp. M10
AC630M Comp. M30
0 AC630M Comp. M10
InsertDNMG 150408 NGUAC630M
InsertDNMG 150408 NEXAC630M Cutting Conditionsvc=150m/min,f =0,15mm/rev,doc=1,6mm,Wet
Cutting Conditionsvc=130m/min,f =0,4mm/rev,doc=0,5mm,Wet
AC520U
X5CrNi1810, Machine Component Grooving X5CrNiMo1810, Measuring Component
Enables stable machining without chattering thanks to excellent chip control
ONuto.pouft (Wpcors)k /pieCcutetisng edge 8 8- performance and a high rigidity holder.
2,7x2to.7olxlitfoeol life
4- 2
30
4
0
0 AC530U Comp. M30
AC520U Comp. M30
InsertCNMG 120408 NEXAC520U Insert: GCM N3002GG (AC520U) Toolholder: GNDL R2525M320
Cutting Conditionsvc=150m/min,f =0,2mm/rev,doc=2,0mm,Wet
Cutting Conditions: vc=60m/min, f =0,025mm/rev, doc=2,0mm, Wet, Cutting edge: 3mm
AC530U
X12CrS13, Pulley Shaft Cutting Off Round Hollow X10CrNiS18 9, Pipe
Enables stable machining thanks to superior cutting performance and excellent
Output (pcs) / Cutting edge 3.0003,-000 chip control.
No. of Workpieces
2,500 1,8x tool life 1.8x tool life
2.0002,-000
1.0001,-500 35
1,000 40
0 5A0C0530U Conventional
0 ACT5oo3l 0U Conventional Tool
InsertBTR3515AC530U Insert: GCMR2002CG05 (AC530U) Toolholder: GNDL R2020K220
Cutting Conditionsvc=60 ~ 90m/min,f =0,04mm/rev,doc=1,5 ~ 2,5mm,Wet Cutting Conditions: vc=140m/min, (n=1.000rpm), f =0,03mm/rev, Wet, Cutting edge: 2mm
www.sumitomo-tools.ru A17
для заказа - sumitomo@sumitomo-tools.ru