Sumitomo - Полный каталог инструмента - 2016 EN
Application Examples (2) для заказа - sumitomo@sumitomo-tools.ru
SteelSteel
Application Examples Insert
Selection
AC820P
Ck45, Turbine Hub 20Cr4, Output Shaft
Good stability and wear resistance in rough cutting of mill-scaled Good wear resistance in high-speed conditions and 2,7x tool
work with 1,6x tool life. life.
No. of Workpieces 300 300 - No. of Workpieces400 400 -
Output (pcs) / Cutting edge200 200 - Output (pcs) / Cutting edge
1.6xtool1life,6x tool life 300 300 - 2.7xtool2life,7x tool life
200 200 -
100 100 - 100 100 -
0 0 0
0 AC820APCC8o2nv0PeP2n0tioCnaolnvPe2n0tional AC820P ACCon8vPe21n00tiPonalConvPe1n0tional
Insert: CNMG 120408 NGE (AC820P) Insert: CNMG 120408 NSX (AC820P)
Cutting Conditions: vc =210m/min, f =0,3mm/rev, doc =1,0mm, Wet Cutting Conditions: vc = ~ 400m/min, f =0,25mm/rev, doc =0,5 ~1,2mm, Wet
34CrMo4, Balancer 15CrMo5, Turbine Hub
High reliability in interrupted cutting with 1,7x tool life. Low alloy steel and good finishing. Stable cutting with 1,8x tool life.
ONuto.puotf(pWcosr)k/piCeutctiesng edge 6600 - No. of Workpieces 1,0010.000 - 1.8x1too,l8lifex tool life
Output (pcs) / Cutting edge 500500 -
11.7,x7toxollitfeool life
3300 -
00 0 0
ACA82C08P20CPonvCPe2no0tniovPnea2nl0tional AC820APC8C2o0nPvPe2n0tCioonnalvPe2n0tional
Insert: WNMG 080408 NGU (AC820P) Insert: CNMG 120408 NGU (AC820P)
Cutting Conditions: vc =220m/min, f =0,18mm/rev, doc =1,0mm, Wet Cutting Conditions: vc =200m/min, f =0,25mm/rev, doc =2,0mm, Wet
Ck45, Compact Knuckle C45, Ring
No sudden breakages and significantly improved stability with Good wear resistance in rough cutting of mill-scaled work and
2,5x tool life. 1,5x tool life.
110000- 22,5.5xxtootolliofel lifeOuNtop.utof(pWcso)r /kpiCuetctiensg edge No. of Workpieces 500 1.5x tool life
Output (pcs) / Cutting edge 500 -
5500- 250 1,5x tool life
250 -
00 AACC882200PP CoCnovPne1nvP0tei1onn0tiaolnal 0 ACA82C08P20PConCvTeoonnotvlioennatlional
0
Insert: WNMG 080412 NLU (AC820P)
Cutting Conditions: vc =192m/min, f =0,45mm/rev, doc =1,0 ~ 2,0mm, Wet Tool
Insert: DNMG 150612 NSX (AC820P)
Cutting Conditions: vc =200m/min, f =0,15 ~ 0,35mm/rev, doc =1,0 ~ 2,0mm, Wet
25CrMo4, Gear C35, Carrier Flange
Good wear resistance in high-feed conditions with 1,8x tool life. Positive type with good wear resistance and 2,2x tool life.
No. of Workpieces 300300 - 1.8x1too,ll8ifex tool life No. of Workpieces 200 300 - 2.2xto2ol,li2fe x tool life
Output (pcs) / Cutting edge 200200 - Output (pcs) / Cutting edge 150 200 -
100100 - 100 100 -
0 0 0 A0C820APC82Co0nPvTeonoCtlioonnavl entional
AC820APC8C2o0nvPPe2n0tiConoanlvPe2n0tional Tool
Insert: CNMG 120408 NMU (AC820P) Insert: DCMT 11T308 NSU (AC820P)
Cutting Conditions: vc =220m/min, f =0,5mm/rev, doc =5mm, Wet Cutting Conditions: vc =180m/min, f =0,17mm/rev, doc =1mm, Wet
www.sumitomo-tools.ru A9
для заказа - sumitomo@sumitomo-tools.ru