Sumitomo - Полный каталог инструмента - 2016 EN
ZX Coated UP MILL для заказа - sumitomo@sumitomo-tools.ru
ZX Coated UP MILL
SSUP 4000ZX Type SSUP 4000ZX-R Type
With Radius Corner
Coated carbide grade: ACZ50M Coated carbide grade: ACZ50M
Helix angle : 40 D Tolerance (mm) Helix angle : 40 D Tolerance (mm)
Corner : Sharp edge D 3,0 – 0,014 – 0,028 Corner : Sharp edge D 3,0 – 0,014 – 0,028
3,0 < D 6,0 – 0,020 – 0,038 3,0 < D 6,0 – 0,020 – 0,038
Endmills 6,0 < D – 0,025 – 0,047 6,0 < D – 0,025 – 0,047
Cat. No. (mm) Endmills (mm)
SSUP 4020ZX Stock D l L d Cat. No. Stock D R l L d
SSUP 4030ZX
SSUP 4040ZX l 2,0 6 50 4 SSUP 4030ZX-R02 l 3,0 0,2 8 50 6
SSUP 4050ZX l 3,0 8 50 6 SSUP 4030ZX-R05 q 3,0 0,5 8 50 6
SSUP 4060ZX l 4,0 11 50 6 SSUP 4040ZX-R02 l 4,0 0,2 11 50 6
SSUP 4070ZX l 5,0 13 60 6 SSUP 4040ZX-R05 l 4,0 0,5 11 50 6
SSUP 4080ZX l 6,0 13 60 6 SSUP 4040ZX-R10 q 4,0 1,0 11 50 6
SSUP 4090ZX l 7,0 16 70 8 SSUP 4050ZX-R02 l 5,0 0,2 13 60 6
SSUP 4100ZX l 8,0 19 80 8 SSUP 4050ZX-R05 l 5,0 0,5 13 60 6
SSUP 4110ZX l 9,0 19 90 10 SSUP 4050ZX-R10 q 5,0 1,0 13 60 6
SSUP 4120ZX l 10,0 22 90 10 SSUP 4060ZX-R03 l 6,0 0,3 13 60 6
SSUP 4140ZX l 11,0 22 90 12 SSUP 4060ZX-R05 l 6,0 0,5 13 60 6
SSUP 4150ZX l 12,0 26 90 12 SSUP 4060ZX-R10 l 6,0 1,0 13 60 6
SSUP 4160ZX l 14,0 26 110 16 SSUP 4060ZX-R15 q 6,0 1,5 13 60 6
SSUP 4180ZX q 15,0 26 110 16 SSUP 4080ZX-R03 l 8,0 0,3 13 80 8
SSUP 4200ZX l 16,0 32 115 16 SSUP 4080ZX-R05 l 8,0 0,5 13 80 8
q 18,0 32 120 20 SSUP 4080ZX-R10 l 8,0 1,0 19 80 8
l 20,0 38 125 20 SSUP 4080ZX-R15 q 8,0 1,5 19 80 8
SSUP 4080ZX-R20 q 8,0 2,0 19 80 8
SSUP 4100ZX-R03 l 10,0 0,3 22 90 10
SSUP 4100ZX-R05 l 10,0 0,5 22 90 10
SSUP 4100ZX-R10 l 10,0 1,0 22 90 10
SSUP 4100ZX-R15 q 10,0 1,5 22 90 10
SSUP 4100ZX-R20 q 10,0 2,0 22 90 10
SSUP 4120ZX-R05 l 12,0 0,5 26 90 12
SSUP 4120ZX-R10 l 12,0 1,0 26 90 12
SSUP 4120ZX-R15 l 12,0 1,5 26 90 12
SSUP 4120ZX-R20 q 12,0 2,0 26 90 12
SSUP 4120ZX-R30 q 12,0 3,0 26 90 12
SSUP 4160ZX-R10 l 16,0 1,0 32 115 16
SSUP 4160ZX-R15 l 16,0 1,5 32 115 16
SSUP 4160ZX-R20 q 16,0 2,0 32 115 16
SSUP 4160ZX-R30 q 16,0 3,0 32 115 16
SSUP 4200ZX-R10 l 20,0 1,0 38 125 20
SSUP 4200ZX-R15 q 20,0 1,5 38 125 20
SSUP 4200ZX-R20 q 20,0 2,0 38 125 20
SSUP 4200ZX-R30 q 20,0 3,0 38 125 20
Coated
Endmills
Cutting data
Recommended cutting conditions
Material Carbon steel, Alloy steel, Hardened steel Stainless steel Heat resistant alloys Shoulder cutting Slotting
Cast iron Prehardened steel Speed Feed Titanium alloy
D (HRC40~50) (HRC20~45)
(mm) (HB150~250) (HRC25~35) Speed Feed
Speed Feed Speed Feed (rpm) (mm/min) Speed Feed
2
4 (rpm) (mm/min) (rpm) (mm/min) 4000 320 (rpm) (mm/min) (rpm) (mm/min)
6 3000 380
8 9000 720 6000 430 2500 380 5500 320 2600 120 doc
10 6600 800 4500 450 2000 400 4000 320 2000 120 doc
12 4800 960 3000 480 1500 400 3000 480 1200 120
14 3600 1000 2200 610 1200 380 2000 520 1000 140 D D
16 2800 1000 1800 610 1000 360 1700 550 160 woc
18 2400 950 1500 550 1500 500 800 140
20 2200 880 1300 490 800 300 1200 430 700 130 (1) Cutting performance is improved
Shoulder doc 1800 650 1100 420 750 270 1000 360 600 120 when using a high rigidity
cutting woc 1600 580 1000 360 700 250 340 500 110 machine.
Slotting doc 1400 500 900 300 450 100
900 330 1,5D 820 400 (2) Speeds and feeds should be
0,05D reduced when slotting some
0,1D 0,2D 0,1D 0,05D stainless steels.
1,0D 0,3D 0,2D
(3) In case of chatter first check the
cutting conditions.
www.sumitomo-tools.ru J29
для заказа - sumitomo@sumitomo-tools.ru