Sumitomo - Полный каталог инструмента - 2016 EN
для заказа - sumitomo@sumitomo-tools.ru
GSX MILL Ball Endmills
GSXB 20000 Type
Structual Steel
Carbon Steel
Alloy Steel
Pre-hardened
Steel
Tempered
Die Steel
Stainless
Steel
Ti Alloy / Heat
Resistant Alloy
Cast iron
Al Alloy
Cu Alloy
Graphite
Coated GSX Hardened Steel Endmills (mm)
Carbide Coating 45~55 55~60 60~65 Cat. No. L d
Grades HRC HRC HRC GSXB 20020
GSXB 20030 50 4
GSXB 20050 50 4
GSXB 20075 50 4
2 GSXB 20100 Stock R D 12 50 4
GSXB 20125 60 6
( D) (mm) GSXB 20150 l 0,20 0,4 0,6 0,8 60 6
40 GSXB20000 GSXB 20200 l 0,30 0,6 0,9 1,2 60 6
GSXB 20250 l 0,50 1,0 1,5 2,0 70 6
30 GSXB 20300 l 0,75 1,5 2,5 3,0 80 6
30° GSXB 20350 l 1,00 2,0 3,0 4,0 80 6
GSXB 20400 l 1,25 2,5 4,0 5,0 90 8
20 GSXB 20500 l 1,50 3,0 4,5 6,0 90 8
GSXB 20600 l 2,00 4,0 6,0 8,0 100 10
Helix Angle 10 GSXB 20700 l 2,50 5,0 7,5 10,0 110 12
0 20 40 60 80 100 ( 1) GSXB 20800 l 3,00 6,0 9,0 – 110 16
GSXB 20900 l 3,50 7,0 11,0 20,0 140 16
Coated carbide grade: ACB20 GSXB 21000 l 4,00 8,0 12,0 – 140 20
GSXB 21250 l 5,00 10,0 15,0 – 160 20
n Endmill Identification (GSXB Type) GSXB 21500 l 6,00 12,0 18,0 – 180 25
l 7,00 14,0 21,0 38,0 180 32
GSXB 2 0200 l 8,00 16,0 24,0 –
l 9,00 18,0 27,0 50,0
l 10,00 20,0 30,0 –
38,0 –
Series No. of Radius 12,50 25,0 45,0 80,0
Code Teeth of 15,00 30,0
Ballnose
New ”Global Standard” Mills
Ball nose type with 2 teeth
Recommended cutting conditions
(1) If cutting noise and vibration are present, please change the cutting conditions accordingly.
(2) If the machine is not designed to achieve the recommended spindle speed, please use the max. spindle speed available.
Coated woc
Endmills
doc
l Radius Milling
Work Material Carbon Steel, Alloy Steel Carbon Steel, Alloy Steel Cast Iron Stainless Steel
(Below 25HRC) (Below 50HRC) Special Cast Iron Titanium Alloy
Cutting Conditions
Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate
R (mm)
0,20 (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min)
0,30
0,50 50.000 2.100 35.000 1.150 50.000 2.100 50.000 1.750
0,75 50.000 2.500 35.000 1.350 50.000 2.500 50.000 2.100
1,00 50.000 3.000 35.000 1.600 50.000 3.000 50.000 2.500
1,25 35.000 3.000 24.000 1.650 35.000 3.200 34.000 2.500
1,50 27.500 3.000 19.000 1.700 35.000 3.900 26.000 2.500
2,00 22.500 3.000 15.500 1.700 28.000 3.900 21.000 2.500
2,50 19.000 3.000 13.000 1.700 24.000 3.900 17.500 2.500
3,00 17.000 3.800 12.000 2.100 20.000 4.100 15.000 2.700
3,50 15.500 4.300 11.000 2.200 18.000 4.600 12.000 2.500
4,00 14.000 4.700 10.500 2.500 16.500 5.300 10.500 2.500
5,00 12.500 4.200 9.000 2.100 14.000 4.500 9.000 2.200
6,00 11.000 3.500 7.900 1.900 12.500 4.000 7.800 1.900
7,00 9.000 2.800 6.300 1.500 10.500 3.300 6.300 1.500
8,00 7.500 2.400 5.200 1.250 8.700 2.800 5.200 1.250
9,00 6.400 2.100 4.500 1.100 7.400 2.400 4.500 1.100
5.600 1.800 3.900 950 6.500 2.100 3.900 950
10,00 5.000 1.600 3.500 850 5.800 1.900 3.500 850
12,50 4.500 1.450 3.100 750 5.200 1.700 3.150 750
15,00 3.600 1.150 2.500 600 4.200 1.350 2.500 600
Depth and wide of cut wdoocc 3.000 960 2.100 500 3.500 1.150 2.100 500
0,02 D 0,02 D 0,02 D 0,02 D
0,05 D 0,05 D 0,05 D 0,05 D
J36 l = Euro stock www.sumitomo-tools.ru
s = To be replaced by new item для заказа - sumitomo@sumitomo-tools.ru