Sumitomo - Полный каталог инструмента - 2016 EN
для заказа - sumitomo@sumitomo-tools.ru
Radius Endmill for Exotic Alloys 4 4 Flutes Endmills with Radius Corner and
SSEH 4000W-R Type HAIMER's SAFE-LOCK TM Applicable Endmills
Coated GS Structual Steel Hardened Steel Stainless
Carbide Carbon Steel Steel
Grades HARD Alloy Steel 45~55 55~60 60~65 Ti Alloy / Heat
Pre-hardened HRC HRC HRC Resistant Alloy
Steel Cast iron
Tempered Al Alloy
Die Steel Cu Alloy
Graphite
Coating
D d h6
+0,02 L Applicable Endmills
r –0,01 ( D) (mm)
40 SSEH4000W-R
4 45° 30
Helix Angle 20
Endmills 10
Cat. No. 0 20 40 60 80 100 ( 1)
SSEH 4045W-R05
SSEH 4045W-R10 Grade: ACW52
SSEH 4050W-R05
SSEH 4050W-R10 Stock D 12 (mm) Endmills Stock D 12 (mm)
SSEH 4060W-R10
SSEH 4080W-R10 l 4,5 0,5 12 L d Cat. No. q 12,0 1,0 26 L d
SSEH 4100W-R10 l 4,5 1,0 12 SSEH 4120WS-R10 q 12,0 3,0 26
SSEH 4100W-R30 l 5,0 0,5 13 50 6 SSEH 4120WS-R30 q 16,0 1,0 32 90 12
SSEH 4120W-R10 l 5,0 1,0 13 50 6 SSEH 4160WS-R10 q 16,0 3,0 32 90 12
SSEH 4120W-R30 l 6,0 1,0 13 60 6 SSEH 4160WS-R30 q 20,0 1,0 40 115 16
SSEH 4160W-R10 l 8,0 1,0 19 60 6 SSEH 4200WS-R10 q 20,0 3,0 40 115 16
SSEH 4160W-R30 l 10,0 1,0 22 60 6 SSEH 4200WS-R30 q 25,0 1,0 50 125 20
SSEH 4200W-R10 l 10,0 3,0 22 80 8 SSEH 4250WS-R10 q 25,0 3,0 50 125 20
SSEH 4200W-R30 l 12,0 1,0 26 90 10 SSEH 4250WS-R30 140 25
SSEH 4250W-R10 l 12,0 3,0 26 90 10 140 25
SSEH 4250W-R30 l 16,0 1,0 32 90 12
l 16,0 3,0 32 90 12
q 20,0 1,0 40 115 16
q 20,0 3,0 40 115 16
q 25,0 1,0 50 125 20
q 25,0 3,0 50 125 20
140 25
140 25
n Diameter and Corner Radius Selection Range
D r 0,5 r 1,0 r 3,0
4,5 l l
l l l
5 l l
Coated 6 l l
Endmills 8 l q
10 l q
doc 12l
doc 16q
20 q
25
Recommended cutting conditions
1. For stable machining, a more rigid machine is recommended.
2. Wet machining is recommended for stainless steel and heat resistant alloy applications.
3. If cutting noise and vibration are present, please change the cutting conditions accordingly.
woc D
l Shoulder Milling l Grooving
Work Material Stainless Steel Titanium Alloy Heat Resistive Steel Work Material Stainless Steel Titanium Alloy Heat Resistive Steel
Cond. Cond.
Spindle Speed Feed Rate
D (mm) Spindle Speed Feed Rate (rpm) (mm/min) Spindle Speed Feed Rate D (mm) Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate
(rpm) (mm/min) 3.500 280 (mm/min) (rpm) (mm/min) (mm/min) (mm/min)
3.200 320 (rpm) 4,5 (rpm) (rpm)
4,5 3.500 350 2.700 320 170 5,0 4,200 200 270 100
5,0 3.200 380 2.000 280 2.100 190 6,0 3,800 240 3,900 300 1,400 120
6,0 2.700 430 1.600 260 1.900 190 8,0 3,200 260 3,500 300 1,300 140
8,0 2.000 400 1.300 230 1.600 170 10,0 2,400 240 2,900 270 1,100 120
10,0 1.600 380 1.000 200 1.200 160 12,0 1,900 220 2,200 250 110
800 160 1.000 140 16,0 1,600 200 1,700 230 800 100
12,0 1.300 360 640 130 120 20,0 1,200 130 1,400 200 650
16,0 1.000 320 1,5 D 800 100 25,0 1,100 550 80
20,0 800 260 0,05 D 600 950 95 90 400 60
25,0 640 200 480 80 760 75 890 70 320 50
Shoulder doc 380 700 250
cutting woc
0,1 D 0,05 D Grooving doc 0,3 D 0,2 D 0,15 D
J24 l = Euro stock s = To be replaced by new item
q = Delivery on request www.sumitomo-tools.ru
для заказа - sumitomo@sumitomo-tools.ru