Sumitomo - Полный каталог инструмента - 2016 EN
4 4 Flutes Endmills для заказа - sumitomo@sumitomo-tools.ru
GSX MILL Endmills
GSX 40000C-4D Type
Structual Steel Stainless
Carbon Steel Steel
Alloy Steel Ti Alloy / Heat
Pre-hardened Resistant Alloy
Steel Cast iron
Tempered Al Alloy
Die Steel Cu Alloy
Graphite
Coated GSX Hardened Steel Endmills
Carbide (mm)
Grades Coating 45~55 55~60 60~65 Cat. No.
HRC HRC HRC GSX 40100C-4D
GSX 40150C-4D
GSX 40200C-4D
GSX 40250C-4D
D d h5 GSX 40300C-4D Stock D 1 2L d
GSX 40400C-4D
GSX 40500C-4D l 1,0 4,0 5,0 40 4
GSX 40600C-4D 4
1 GSX 40800C-4D l 1,5 6,0 7,0 40 4
2 GSX 41000C-4D 4
GSX 41200C-4D l 2,0 8,0 9,0 40 6
GSX 41600C-4D 6
L GSX 42000C-4D l 2,5 10,0 11,0 50 6
6
30° l 3,0 12,0 13,5 50 8
10
( D) (mm) l 4,0 16,0 17,5 50 12
40 GSX40000C-4D 16
l 5,0 20,0 22,0 60 20
30
Helix Angle Corner : C Type 1.5D 2D 3D l 6,0 24,0 – 60
20 4D
Dc Tolerance 10 l 8,0 32,0 – 80
D 3,0 0 – 0,015
0 – 0,020 l 10,0 40,0 – 90
3,0 < D 12 0 – 0,030
0 20 40 60 80 100 ( 1) l 12,0 48,0 – 100
12,0 < D
Grade: ACF20
l 16,0 64,0 – 120
20,0 80,0 – 140
n Endmill Identification (GSX MILL Series)
GSX 4 0100 C - 4D
j k l m n
Series No. of Diameter Cutting Cutting Edge
Code Teeth Edge Length
( )S: Sharp Edge
C: Gash Land Drilling
n Recommended Cutting Conditions Coated
Endmills
1. For stable machining performance use rigid, high-precision machines and holders.
2. Use air blowing when dry machining. doc
3. Use wet machining for stainless steel, heat resistant alloy, and titanium alloy applications.
4. In rear cases, chattering may occur in early milling stages, dissipating after 2m of cutting. woc
5. If chattering is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or
reduce the depth of cut.
6. This series is not recommended for grooving.
7. If the machine cannot achieve the recommended spindle speed, please use the max. spindle speed available.
l Shoulder Milling
Work Material Carbon Steel Cast Iron Alloy Steel Tempered Steel, Hardened Steel Stainless Steel Heat Resistive
Structural Steel (150 to 250HB) (25 to 35HRC) Hardened Steel (45 to 55HRC) Steel,
(35 to 45HRC)
Cond. Titanium Alloy
D (mm) Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate
(rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min)
1,0 9.000 140 9.000 140 9.000 140 7.000 80 6.500 60 4.500 40 5.400 40 4.500 40
2,0 4.500 140 4.500 140 4.500 140 3.500 100 3.200 80 2.300 55 2.700 55 2.300 40
4,0 2.250 200 2.250 200 2.250 200 1.750 120 1.600 100 1.200 60 1.350 50 1.200 35
6,0 1.500 250 1.500 250 1.500 250 1.150 160 1.050 140 800 65 900 45 800 35
8,0 1.100 220 1.100 220 1.100 220 850 160 800 130 600 65 660 45 600 35
10,0 900 210 900 210 900 210 700 140 650 120 460 65 540 45 460 35
12,0 750 200 750 200 750 200 580 140 520 110 400 65 450 45 400 35
16,0 550 170 550 170 550 170 440 120 400 95 300 55 330 45 300 35
20,0 450 150 450 150 450 150 350 100 320 80 240 50 270 45 240 35
wdoocc 3,5 D 3,0 D
Shoulder D< 3: 0,04 D , 3 D< 8: 0,08 D , 8 D: 0,1 D 0,02 D
cutting
www.sumitomo-tools.ru J19
для заказа - sumitomo@sumitomo-tools.ru