Sumitomo - Полный каталог инструмента - 2016 EN
для заказа - sumitomo@sumitomo-tools.ru
Wave Radius Mill Multi Purpose Endmills with Polygon Inserts
WRCX 08000/10000 E Type
4,0 mm 5,0 mm
Shank Type with Small Diameter Inserts
E _ : Cylindrical straight shank type Axial rake angle: – 3°
Radial rake angle: 0 ~ 35°
ES : Short type with straight shank
EM : Middle length type with straight shank
EL : Long type with straight shank
Body Spare Parts
Insert Cat. No. Stock D Dimensions (mm) No. of Axial Radial Helical Boring Plunging BFTX 02505 IP
C d1 d2 l1 l2 l3 teeth Rake Rake B Standard BFTX 02506 IP
IC (mm) a max.
BFTX 03584 IP
WRCX 08012 ES l 12 - 12 9,4 110 40 70 1 -3° -35° – 0°30 TRDR 08 IP
WRCX 08012 EM l 12 - 12 9,4 150 70 80 1 TRDR 08 IP
TRDR 15 IP
WRCX 08016 ES l 16 - 16 14 120 50 70 1 -3° - 10° 24 + 7 5°30
WRCX 08016 EM l 16 - 16 14 150 70 80 1 - 4
WRCX 08020 ES l 20 12 20 18 130 50 80 2 -3° -3 ° 32 ± 7 13°
WRCX 08020 EM l 20 12 20 18 180 100 80 2
8 WRCX 08020 EL l 20 12 20 18 250 130 120 2
WRCX 08025 ES l 25 17 25 21 130 50 80 3
WRCX 08025 EM l 25 17 25 21 180 100 80 3 -3° 0° 42 ± 7
8°20
WRCX 08025 EL l 25 17 25 21 250 130 120 3
WRCX 10025 ES l 25 15 25 21 130 50 80 2
WRCX 10025 EM l 25 15 25 21 180 100 80 2 -3° 0° 40 ± 8 13°10
WRCX 10025 EL l 25 15 25 21 250 130 120 2
WRCX 10032 ES l 32 22 32 28 130 50 80 3 -3° 0° 54 ± 8 8°
10 WRCX 10032 EM l 32 22 32 28 200 120 80 3
WRCX 10032 EL l 32 22 32 28 300 180 120 3
Insert
Indexable QPMT... : Standard 16 cornered polygon type QPET...- S : Polished round insert for non-ferrous material
Endmills QPMT...- H : Stronger cutting edge type
Fig. 1 Fig. 2 Rake angle: 25°
4 corners use
R : wiper radius
Cat. No. Coated Carbide Diamond Uncoated IC r s Max. doc Fig. Applicable
Coated carbide 4 corners 8 corners Endmill
QPMT 080330 PPEN application application u
QPMT 080330 PPEN-H ACP100 ACP200 ACP300 ACK200 ACK300 DL1000 H1 (mm) (mm) (mm) WRCX 08000 E
QPMT 10T335 PPEN u
QPMT 10T335 PPEN-H l l l l l 8 3,0 3,18 3,8 1,0 v WRCX 10000 E
QPET 10T350 PPFR-S l l l l l
l l l l l 10 3,5 3,9 7 4,7 1,2
l l l l l
l l 5,0 –
Recommended Cutting Conditions
[vc = m/ min, f t = mm/ tooth] [min.– optimum – max.]
Material Carbon steel Alloy steel Stainless steel Cast iron Non-ferrous
(ex. C40 ~ C50) (Below HRC40) (ex. X10CrNiS18-9) (ex. GG20) material
D Grade
(mm) ACP100, ACP200 ACP100, ACP200 ACP200, ACP300 ACK200, ACK300 DL1000, H1
200-500-1000
12 ~ vc 80-120-160 60-100-140 60-100-120 60-80-120
32 f t 0,1-0,3-0,4 0,1-0,2-0,3 0,1-0,15-0,2 0,1-0,2-0,3 0,1-0,2-0,3
H34 l = Euro stock www.sumitomo-tools.ru
q = Delivery on request для заказа - sumitomo@sumitomo-tools.ru