Sumitomo - Полный каталог инструмента - 2016 EN
для заказа - sumitomo@sumitomo-tools.ru
”METAL SLASH MILL”
MSX Type
Recommended Cutting Conditions
Coated Cutting Insert Endmill Type (D) Shell Type (D)
Carbide Speed Cat.
Work Grade vc (m/min) No. 16 20 25 32 40 50~66 80~100
Material
doc Feed rate doc Feed rate doc Feed rate doc Feed rate doc Feed rate doc Feed rate doc Feed rate
(mm) (mm/tooth) (mm) (mm/tooth) (mm) (mm/tooth) (mm) (mm/tooth) (mm) (mm/tooth) (mm) (mm/tooth) (mm) (mm/tooth)
WDMT 0603 0,8 0,8 0,8 0,8 0,8 0,8 – – – – – – – –
General Steel ACP200 100-150-200 WDMT 0804 – – 1,0 1,0 1,0 1,2 1,0 1,2 – – – – – –
(Below HB200) WDMT 1205 – – – – – – 1,2 1,4 1,2 1,4 1,2 1,4 – –
WDMT 1406 – – – – – – – – 1,5 1,5 1,5 1,5 1,5 1,5
WDMT 0603 0,7 0,8 0,7 0,8 0,7 0,8 – – – – – – – –
Alloy Steel ACP200 80-130-180 WDMT 0804 – – 0,8 1,0 0,8 1,2 0,8 1,2 – – – – – –
(Below HRC45) WDMT 1205 – – – – – – 1,0 1,4 1,0 1,4 1,0 1,4 – –
WDMT 1406 – – – – – – – – 1,3 1,5 1,3 1,5 1,3 1,5
Stainless Steel WDMT 0603 0,8 0,7 0,8 0,7 0,8 0,7 – – – – – – – –
X5CRNI1810, ACP300
80-120-150 WDMT 0804 – – 1,0 0,8 1,0 0,8 1,0 0,8 – – – – – –
Others WDMT 1205 – – – – – – 1,2 1,2 1,2 1,2 1,2 1,2 – –
WDMT 1406 – – – – – – – – 1,5 1,3 1,5 1,3 1,5 1,3
WDMT 0603 0,8 1,0 0,8 1,0 0,8 1,0 – – – – – – – –
Cast Iron ACK300 100-150-200 WDMT 0804 – – 1,0 1,2 1,0 1,4 1,0 1,4 – – – – – –
GG, GGG WDMT 1205 – – – – – – 1,2 1,5 1,2 1,5 1,2 1,5 – –
WDMT 1406 – – – – – – – – 1,5 1,8 1,5 1,8 1,5 1,8
WDMT 0603 0,5 0,5 0,5 0,5 0,5 0,5 – – – – – – – –
Hardened Steel ACK300 40-80-100 WDMT 0804 – – 0,5 0,6 0,5 0,8 0,5 0,8 – – – – – –
(Below HRC50) WDMT 1205 – – – – – – 0,6 1,0 0,6 1,0 0,6 1,0 – –
WDMT 1406 – – – – – – – – 1,0 1,2 1,0 1,2 1,0 1,2
Insert Cat. No. Max doc r l The above recommended cutting conditions may require adjustment according to machine rigidity and work rigidity.
WDMT 0603.... 1,0 1,5 The above figures are guidelines for use with the BT50 machine tool.
WDMT 0804.... 1,5 2,0
WDMT 1205.... 2,0 2,0 l The above cutting conditions assume a tool overhang length of L/D=3 (i.e. overhang length is 3 times tool diameter) or less.
WDMT 1406.... 2,5 2,0 When tool overhang is more than L/D=3 and less than or equal L/D=5, settings should be adjusted to approximately
70 to 80% of those indicated in the above cutting conditions (i.e. doc and Feed Rate).
When tool overhang is more than L/D=5 and less than or equal L/D=8, settings should be adjusted to approximately
50 to 60% of those indicated in the above cutting conditions (i.e. doc and Feed Rate).
Information for Programming Indexable
Endmills
For machine programming, please use the theoretical corner radius (R) shown in the list.
Maximum depth (d) between theoretical radius and actual profile will be left on the finished surface, as shown below.
Body Insert Theoretical Radius (R) Remaining Depth (d)
MSX 06000 WDMT 0603.... 2,0 0,403
MSX 08000 WDMT 0804.... 2,5 0,593
d MSX 12000 WDMT 1205.... 3,0 1,030
MSX 14000 WDMT 1406.... 3,5 1,219
Plunging and Helical Boring WDMT0603ZDTR WDMT0804ZDTR WDMT1205ZDTR WDMT1406ZDTR
Ramping Cutter doc : max 1,0 doc : max 1,5 doc : max 2,0 doc : max 2,5
doc: Max. Depth
a: Max. Angle Ramping Helical boring Ramping Helical boring Ramping Helical boring Ramping Helical boring
Helical Boring a min. max. a min. max. a min. max. a min. max.
max. B B max. B B max. B B max. B B
16 6°00’ 21 31
17 5°00’ 23 33
18 4°30’ 25 35
20 3°30’ 29 39 7°30’ 25 38
5°30’ 29 42
22 3°00’ 33 43 4°00’ 35 48
3°00’ 41 54
25 2°00’ 39 48 2°30’ 49 62
2°00’ 55 68
28 1°30’ 65 78
32 6°30’ 42 63
5°00’ 48 69
35
4°00’ 58 79
40 2°30’ 78 99 6°00’ 53 78
2°00’ 103 124 3°30’ 73 98
50 1°30’ 109 130 2°00’ 99 124
1°45’ 105 130
63
1°30’ 133 158
66 1°00’ 173 198
B min. B max. 80
100
www.sumitomo-tools.ru H11
для заказа - sumitomo@sumitomo-tools.ru