Sumitomo - Полный каталог инструмента - 2016 EN
для заказа - sumitomo@sumitomo-tools.ru
Exchangeable Head Endmills
Modular Tools
Carbide and Steel Arbor for Modular Tools
Carbide Arbor
Steel Arbor
Carbide Arbor Steel Arbor
Cat. No. Stock M Dimensions (mm) LM Cat. No. Stock M Dimensions (mm) LM
d D L l1 l2 d D L l1 l2
MA 15 M08 L120C l M8 8,5 15 120 10 18 145 MA 16 M08 L120S l M8 8,5 16 120 10 18 145
MA 15 M08 L160C MA 20 M10 L150S
MA 16 M08 L120C l M8 8,5 15 160 10 18 185 MA 25 M12 L200S l M10 10,5 20 150 10 20 180
MA 16 M08 L160C MA 32 M16 L200S
MA 18 M10 L150C l M8 8,5 16 120 10 18 145 l M12 12,5 25 200 10 22 235
MA 18 M10 L200C
MA 20 M10 L150C l M8 8,5 16 160 10 18 185 l M16 17,0 32 200 10 24 240
MA 20 M10 L200C
MA 23 M12 L200C l M10 10,5 18 150 10 20 180
MA 23 M12 L250C
MA 25 M12 L200C l M10 10,5 18 200 10 20 230 Identification of Catalogue No.
MA 25 M12 L250C
MA 28 M16 L200C l M10 10,5 20 150 10 20 180
MA 28 M16 L300C
MA 32 M16 L200C l M10 10,5 20 200 10 20 230 MA 15 M08 L120 C
MA 32 M16 L300C
l M12 12,5 23 200 10 22 235
l M12 12,5 23 250 10 22 285 Modular Arbor Mounting Material
C: Carbide
l M12 12,5 25 200 10 22 235 Screw S: Steel
l M12 12,5 25 250 10 22 285 Shank Arbor
Length
l M16 17,0 28 200 10 24 240 Diameter
l M16 17,0 28 300 10 24 340
l M16 17,0 32 200 10 24 240
l M16 17,0 32 300 10 24 340 Recommended Tightening Torque
l Modular Tool System Screw Wrench Torque
( Modular tool head + arbor ) WS ( N.m )
M 8
M10 8 13 23
M12
M16 8 15 46
10 19 80
10 24 90
Notes about tightening the head: Indexable
l Refer to the Head Cat. No. chart on pages H18, H19, H35 and H37 to select the Endmills
arbor size in the table above.
l Check the mounting screw size of the head and arbor beforehand.
l When attaching head to an arbor, follow the standard tighting torque in the table
above.
Application Range
Work Material: C50, Equipment : Vertical Machine M/C BT50 (Dry)
WEX2025M12Z4 4444,,,,0000 ((((mmmmmmmm)))) WEX3035M16Z3 4444,,,,0000 ((((mmmmmmmm))))
3333,,,,0000
(vc =180m/min, ft =0,1mm) Axial Depth of Cut 3333,,,,0000 Overhang (vc =180m/min, ft =0,1mm) Axial Depth of Cut 2222,,,,0000 Overhang
2222,,,,0000 1111,,,,0000
H18 1111,,,,0000 H19
0000
0000 0000,,,,22225555DDDD 0000,,,,5555DDDD 0000,,,,77775555DDDD 111100000000 0000,,,,22225555DDDD 0000,,,,5555DDDD 0000,,,,77775555DDDD 111100000000
111133330000 111133330000
111155550000 111155550000
111188880000 111188880000
1111xxxxDDDD 1111xxxxDDDD
Radial Width of Cut Radial Width of Cut
WRCX10025M12Z2 H35 4444,,,,0000 ((((mmmmmmmm)))) MSX12032M16Z2 2222,,,,0000 ((((mmmmmmmm))))
3333,,,,0000 1111,,,,5555
RSX10025M12Z2 H37 (vc =160m/min, doc =1,2mm)
(vc =160m/min, ft =0,2mm) Axial Depth of Cut Overhang H10 Feed Rate per Tooth Overhang
2222,,,,0000 1111,,,,0000
111100000000 111100000000
111133330000 0000,,,,5555 111133330000
1111,,,,0000 111155550000 111155550000
0000 111188880000 0000 111188880000
0000,,,,22225555RDDDDadial W0000,,,,55i55dDDDDth of C00u00,,,,77t775555DDDD 1111xxxxDDDD 0000,,,,22225555DDRDDadial W0000,,,,55i55dDDDDth of C0000u,,,,77t775555DDDD 1111xxxxDDDD
Note: These tables indicate reference machining conditions. Actual machining parameters should be adjusted based on machine rigidity and work clamp rigidity.
www.sumitomo-tools.ru H5
для заказа - sumitomo@sumitomo-tools.ru