Sumitomo - Полный каталог инструмента - 2016 EN
для заказа - sumitomo@sumitomo-tools.ru
Wave Radius Mill
RSX(F)10000RS/12000RS/16000RS
Various Machining Use
Various types of processing, such as mould engraving, slant milling and helical processing.
Helical Milling Ramping Recommended Values for Helical and Ramping
Helical Milling Use at ° or lower Helical Taper
Insert Cat. No. Cutter Work Diameter Ramping
RDET10... Dc Angle
RDET12... Min. Optimal Max.
RDET16... 25 °(max)
32 33,0 40 49
40 46,0 54 63 10°30‘
50 6°45‘
52 62,0 70 79 4°30‘
32 3°15‘
Work Diameter 40 82,0 90 99 3°10‘
50 12°30‘
52 86,0 94 103 8°00‘
63 5°30‘
66 41,5 52 63 5°15‘
80 4°00‘
Center uncut portion cannot 100 57,5 68 79 3°45‘
be removed by traverse cut- 63 2°50‘
ting with the same cutter. 80 77,5 88 99 2°10‘
100 6°00‘
125 81,5 92 103 4°10‘
3°00‘
103,5 114 125 2°20‘
109,5 120 131
Work Diameter 137,5 148 159
177,5 188 199
Center uncut portion can be 96,0 110 125
removed by traverse cutting
with the same cutter. 130,0 144 159
170,0 184 199
220,0 234 249
Inserts Grade
Application ACM100 d±0,025 s±0,025 Milling Cutters
High Speed/Light Cut ACM200
General Purpose ACM300
Roughing
d±0,025
Cat. No. Dimens. Applicable
RDET 10T3M0EN G d S Cutters
10T3M0EN H (IC)
Cutting Edge Cross Section
RDET 1204M0EN G l l l 10 3,97 RSX(F) 10000RS
1204M0EN H l l l 10 3,97
RDET 1606M0EN G l l l 12 4,76 RSX(F) 12000RS M0: IC is metric
1606M0EN H l l l 12 4,76
G - Type H - Type
l l l 16 6,5 RSX(F) 16000RS
l l l 16 6,5
Spare Parts Wrench Screw Recommended
Tightening
Applicable
Cutters Torque (N·m)
RSX(F) 10000RS TRDR15IP BFTX03584IP 3,0
RSX(F) 12000RS TRDR20IP BFTX0409IP 3,0
RSX(F) 16000RS BFTX0511IP 5,0
Recommended Cutting Conditions Min.-Optimum-Max.
ISO Work Material Hardness Cutting Speed Feed Rate Grade
vc (m/min) ft (mm/t)
CrFerritic 200HB ACM300
200-330HB 150-180-200 0,15-0,25-0,35 ACM300
Stain- Based Martensitic 80-120-180 0,15-0,25-0,35 ACM300
200HB 150-180-200 0,15-0,25-0,35 ACM200
M less Cr-Ni Austenitic 230-270HB 80-120-180 0,15-0,25-0,35 ACM200
Steel Austenitic, ferritic 60-100-160 0,15-0,25-0,35
Based Precipitation hardening 330HB 20- 30- 40 0,10-0,20-0,30 ACM100
250-350HB 60- 80-100 0,10-0,20-0,30 ACM200
Heat resistant alloy Ni based material 40- 50- 60 0,10-0,20-0,30
(Rm400)
S Titanium Pure Titanium (Rm1050)
+ alloy system
www.sumitomo-tools.ru G23
для заказа - sumitomo@sumitomo-tools.ru